MPLAB ? REAL ICE ? In-Circuit Emulator User’s Guide
5.7.2.2
DATA MEMORY TAB
Set up a data memory breakpoint here.
TABLE 5-4:
Control
Address
Breakpoint Type
Pass Count
DATA MEMORY BREAKPOINT
Function
Location of breakpoint in hex
The type of data memory breakpoint. See the device data sheet for
more information on X Bus reads/writes.
X Bus Read – break on an X bus read of above address
X Bus Read Specific Byte – break on an X bus read of above
address for the specific byte value in “Specific Value”
X Bus Read Specific Word – break on an X bus read of above
address for the specific word value in “Specific Value”
X Bus Write – break on an X bus write of above address
X Bus Write Specific Byte – break on an X bus write of above
address for the specific byte value in “Specific Value”
X Bus Write Specific Word – break on an X bus write of above
address for the specific word value in “Specific Value”
Break on pass count condition.
Always break – always break as specified in “Breakpoint type”
Break occurs Count instructions after Event – wait Count (0-255)
instructions before breaking after event specified in “Breakpoint
type”
Event must occur Count times – break only after event specified in
“Breakpoint type” occurs Count (0-255) times
5.7.3
Stopwatch Dialog
The stopwatch allows timing from one breakpoint/trigger condition to the next.
TABLE 5-5:
Control
Start Condition
Stop Condition
STOPWATCH SETUP
Function
Click Select Start Condition to choose an available breakpoint or
trigger condition to start the stopwatch. Available breakpoints/trig-
gers are those previously added to the breakpoint dialog.
Click None to clear the start condition.
To halt the program run on this condition, check the check box next
to “Start condition will cause the target device to halt”.
Click Select Stop Condition to choose an available breakpoint or
trigger condition to stop the stopwatch. Available breakpoints/trig-
gers are those previously added to the breakpoint dialog.
Click None to clear the stop condition.
To halt the program run on this condition, check the check box next
to “Stop condition will cause the target device to halt”.
Reset stopwatch on run
Reset the stopwatch values to zero every time the program is run.
5.7.4
Event Breakpoints Dialog
Select a condition where the program will always break:
? Break on Watchdog Timer – Break every time the watchdog timer times out. Make
sure the Watchdog Timer is enabled in the Configuration bits.
? Break on SLEEP instruction – Break when a SLEEP instruction is encountered in
the program.
DS51616A-page 34
? 2006 Microchip Technology Inc.
相关PDF资料
AC2626M6 PROBE TEMP 6" GENERAL PURP
AC300024 MOTOR STEPPER 2PHASE 8WIRE
AC300030 KIT ACOUSTIC ACCESSORY
ACM-16 CABLE MODULE FR3 16BIT 40-DIP
ACM-2X8 ACTIVE CABLE MODULE DUAL 8 BIT
ACM-8 CABLE MODULE FR3 8BIT 28/32-DIP
ACS9510EVB EVALUATION BOARD FOR ACS9510
ACS9550EVB EVALUATION BOARD FOR ACS9550
相关代理商/技术参数
AC244007 制造商:Microchip Technology Inc 功能描述:MPLAB REAL ICE JTAG ADAPTER - Boxed Product (Development Kits) 制造商:Microchip Technology Inc 功能描述:ADAPTER MPLAB REAL ICE JTA 制造商:Microchip Technology Inc 功能描述:ADAPTER, MPLAB, REAL, ICE, JTAG 制造商:Microchip Technology Inc 功能描述:ADAPTER, MPLAB, REAL, ICE, JTAG; Accessory Type:JTAG adaptor Board; For Use With:Microchip PIC32MX devices; SVHC:No SVHC (19-Dec-2012) ;RoHS Compliant: Yes
AC244008 功能描述:处理器配件 MPLAB REAL ICE Power Monitor RoHS:否 制造商:Olimex Ltd. 产品:Cable 用于:
AC244022 功能描述:插座和适配器 Procs Extnsn Pak for PIC24FJ128GA010-ICE RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
AC244022 制造商:Microchip Technology Inc 功能描述:Processor Extension Pak for PI
AC244023 功能描述:插座和适配器 PROCESSOR EXTNSN PAK FOR PIC18F1xK50 RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
AC244024 功能描述:插座和适配器 Processor Ext Pak for PIC18LF14K50 RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
AC244026 功能描述:插座和适配器 Processor Ext Pak (PIC16F727-ICE) 200K RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x
AC244027 功能描述:插座和适配器 Processor Ext Pak (PIC16LF727-ICE)200K RoHS:否 制造商:Silicon Labs 产品:Adapter 用于:EM35x